Pandora Enclosure System for Prometheus CPU
	For use with Prometheus CPU and Panel I/O Board;  Easy assembly - no internal cables required;  No internal mounting rails or corner guides ;  Pretapped screw holes for clean, professional assembly ;  Available in several sizes to accommodate extra PC/104 boards;  Fits notebook hard drive in addition to boards ;  Isolation-mount option ;  All hardware included...     цены    документация
FEATURES     For use with Prometheus CPU and Panel I/O Board  Easy assembly - no internal cables required  No internal mounting rails or corner guides  Pretapped screw holes for clean, professional assembly  Available in several sizes to accommodate extra PC/104 boards  Fits notebook hard drive in addition to boards  Isolation-mount option  All hardware included   Description Pandora is an enclosure system designed by Diamond Systems for use with our Prometheus PC/104 CPU and PNL-Z32 panel I/O board. It features fast and easy assembly due to the fact that most or all internal cables can be eliminated. Rather than requiring the installation of special corner mounts or forcing the stack into a set of corner guides, the entire stack is bolted directly to the front plate of the case, forming a rugged, easily-handled assembly. The PC/104 Pandora case measures 5.5" wide by 5.75" high. It comes in five lengths: The 1.7"(43.18mm) case accommodates the Prometheus CPU, the panel I/O board, and an optional notebook hard drive. The 3.0"(76.2mm) case accommodates the CPU, panel board, up to two additional PC/104 boards, and an optional notebook hard drive. The 5.0"(127mm) case accommodates the CPU, panel board, up to five additional PC/104 boards, and an optional notebook hard drive. The 7.0"(177.8mm) and 10.0"(254mm) cases provide still more room for installing other circuitry and items inside the box. The 10" case has enough room for a standard desktop type hard drive as well as 2 expansion PC/104 modules. Case lengths accommodate PC/104 boards with stackthrough configuration (long pins on the bottom side) at the bottom of the stack so no special effort is required to obtain non-stackthrough boards or to cut the connector pins. The length is also sufficient to enable mounting a notebook hard drive below the bottom board and attaching it to the rear end plate. The 3.0" length is designed with the intention of accommodating two additional boards. A typical configuration might include a VGA board and a DC/DC power supply for use in mobile applications. However any two boards can be installed. The interior cavity is wide enough to install any PC/104 board with almost any I/O connector, including pin headers with ejector latches. Each Pandora case includes case body, front plate to accommodate the panel board, rear plate, and all mounting hardware (screws and spacers). Additional end plates are available separately. Assembly Method Installation of boards inside Pandora is as follows. The panel board first mounts on top of the CPU. Spacers are installed between the two boards and above the panel board. The panel board is then fitted to the case front plate and attached using 4 screws driven into the spacers as well as screwlocks driven into the 7 Dsub connectors on the panel board. In this fashion the entire CPU assembly is mounted directly and securely to the end plate. This assembly can now be easily attached to the front of the case body using 8 flathead screws. (All necessary hardware is provided with the case and/or the panel board.) The rear plate can now be attached with 8 more screws, and the assembly is complete. Pandora Cross Section Drawings The following cross-section drawings illustrate the relative positions of the components inside the 1.7" and larger cases. These can serve as a quick overview of the proper assembly method. We recommend you start with the face plate and work your way down to ensure that all the mounting hardware aligns properly. End Plates Multiple end plates are available. The standard package includes a front end plate containing cutouts for use with the PNL-Z32 board, (models with and without the data acquisition cutout are available). The rear end plate contains PC/104 mounting holes that may be used to attach to the bottom of the stack using additional spacers if desired for extra rigidity, although for a 2-board system these are not needed. The lengths of the cases have been selected to allow the use of standard PC/104 spacers, such as Diamond Systems' SPC-104, in this configuration. Each Pandora case includes case body, front plate to accommodate the panel board, rear plate, and all mounting hardware (screws and spacers). Additional end plates are available separately. PBEC-03 Isolation Mounting Plate This plate allows for mounting to a wall or bulkhead and includes 4 rubber grommets in the corners to help minimize vibration of the system.